Differences

This shows you the differences between two versions of the page.

Link to this comparison view

--- en:iot-open:remotelab:sut:generalpurpose2:u2 [2019/08/04 12:13] – pczekalski
+++ en:iot-open:remotelab:sut:generalpurpose2:u2 [2020/07/20 09:00] (current) – external edit 127.0.0.1
@@ Line 5: / Line 5: @@
 === Prerequisites ===
-You need to know how to handle 4×20 characters LCD screen. In case of doubt re-work on scenarios B1 and B2.\\ <fc #ff0000>Warning: In no case should you give your AP the internal.IOT SSID name! You will mess up the laboratory environment and block other users from accessing network infrastructure. We consider this behaviour as hacking and it will be penalized under legal jurisdiction!</fc>
+You need to know how to handle 4×20 characters LCD screen. In case of doubt re-work on scenarios B1 and B2.\\ <fc #ff0000>Warning: In no case should you give your AP the ''internal.IOT'' SSID name! You will mess up the laboratory environment and block other users from accessing network infrastructure. We consider this behaviour as hacking and it will be penalized under legal jurisdiction!</fc>
-<note warning>In no case give your AP the internal.IOT SSID! You will mess up the laboratory environment and block other users from accessing network infrastructure. We consider this behaviour as hacking and it will be penalized under legal jurisdiction!</note>
+<note warning>In no case give your AP the ''internal.IOT'' SSID! You will mess up the laboratory environment and block other users from accessing network infrastructure. We consider this behaviour as hacking and it will be penalized under legal jurisdiction!</note>
 To fully experience this scenario, you need to book another node (one of 1,2,3 or 4), to let the other node act as your networking client. You can use scenario U1 for this purpose but mind to update network SSID and passphrase in your code, to let it connect to your server. <note tip>Students physically present in the SUT IoT laboratory room 320 may use their own devices like laptops or mobile phones to connect to your AP.</note>
@@ Line 21: / Line 21: @@
 Following steps do not present full code - you need to supply missing parts on your own!
 == Step 1 ==
-//Describe activities done in Step 1.//
+Include all necessary libraries. The minimum set here is:
+<code c>
+#include <Arduino.h>
+#include <ESP8266WiFi.h>
+#include <LiquidCrystal_I2C.h>
+...
+</code>
+== Step 2 ==
+Give it some definitions as identifiers for cleaner code, remember to change ssid name to yours!
+<code c>
+#define wifi_ssid_ap put_your_unique_id_here //give it some unique name-change here
+#define wifi_password_ap "1234567890"
+</code>
+<note warning>Never use ''internal.IOT'' as your SSID name ''wifi_ssid_ap'' - you will overlap existing network infrastructure and we consider it as hacking that is subject to jurisdiction! Your account will be imediatelly banned!</note>
+== Step 3 ==
+Print some information about starting software WiFi AP, configure network interface as a WiFi AP and give it a try to start:
+<code c>
 ...
+  delay(10);
+...
+  WiFi.mode(WIFI_AP);
+  delay(100);
+  boolean result = WiFi.softAP(wifi_ssid_ap, wifi_password_ap);
+  if(result == true)
+  {
+... //Announce success, print status, SSID and passphrase to the LCD
+  }
+  else
+  {
+... //Announce failure. Print it on LCD
+  }
+...
+</code>
-== Step n ==
+== Step 4 ==
-//Describe activities done in Step n.//
+Implement in the ''loop()'' an information about number of connected clients, i.e. like this:
+<code c>
+...
+void loop()
+{
+  lcd.setCursor(0,3);
+  sprintf(buffer, "Stations: %d", WiFi.softAPgetStationNum());
+  lcd.print(buffer);
+  delay(3000);
+}
+...
+</code>
 === Result validation ===
-//Provide some result validation methods, for self assesment.//
+Check your AP is active on LCD eventually observe failure. If works OK, compile U1 scenario on another node(s), mind to update SSID and passphrase in the U1 source code then observe if connected clients counter increases.
 === FAQ ===
-This section is to be extended as new questions appear. \\
+Do I need to use WiFi.mode(WIFI_AP);?: Yes, please do. Theoretically, if consecutive compilations use AP (software server) mode of the ESP8266 wifi interface, your code may work without it. However, you never know if the previous user used STA or AP (or both). Your code may fail then if not explicitly stated!
-When using the printed version of this manual please refer to the latest online version of this document to obtain the valid and up-to-date list of the FAQ.
-//Provide some FAQs in the following form:\\
-**Question?**: Answer.
-//

en/iot-open/remotelab/sut/generalpurpose2/u2.1564920800.txt.gz · Last modified: 2020/07/20 09:00 (external edit)